|
Joined: Jul 2005
Posts: 32
Member
|
OP
Member
Joined: Jul 2005
Posts: 32 |
I would appreciate any help in this issue: I've got fms(8) card with 1.8 software on the flash. It's acting strange (althrough I didn't try to access it with cosessions), it boots up and after the initialization the run led is blinking (ok), mb led is steady(ok) and bclr is steady red (problem). The channel led's (total 8 of them) getting red within 2-3 minutes after the initialization starting with the channel 8. My questions are: 1. is fms(8) supported on elite 48 2. do I have to initialize the cabinet first to see a vm card? 3. could it be a problem with the board?
Any feedback is appreciated.
|
|
|
Visit Atcom to get started with your new business VoIP phone system ASAP
Turn up is quick, painless, and can often be done same day.
Let us show you how to do VoIP right, resulting in crystal clear call quality and easy-to-use features that make everyone happy!
Proudly serving Canada from coast to coast.
|
|
|
Joined: Mar 2005
Posts: 306
Member
|
Member
Joined: Mar 2005
Posts: 306 |
The system needs to be told what card is in each slot (mem.b. 7-1)The sta/ext. need to be set as dig. v-mail. fms is supported on an elite 48 but you must be under 48 total ports
|
|
|
|
Joined: Dec 2005
Posts: 170
Member
|
Member
Joined: Dec 2005
Posts: 170 |
what is the q version, haved u ran a defrag on the c: drive, you probably have some database errors
|
|
|
|
Joined: Jul 2005
Posts: 32
Member
|
OP
Member
Joined: Jul 2005
Posts: 32 |
Thanks for the input!
Well the things here are very interesting: I'm unable to connect to the vm from cosession (tried all settings) but was successful connecting using hyperterm in vt100 mode. the autoexec.bat is set to the speed of 9600bps which is strange and there is no cossession host software installed (it uses dos's mode.com). Moreover, the directories on the drive are ACD <DIR> 08-05-2002 11:58a BICOM <DIR> 08-05-2002 11:58a DEFAULTS <DIR> 08-05-2002 11:58a DOS <DIR> 08-05-2002 11:58a PCM <DIR> 08-05-2002 11:58a UTILITY <DIR> 08-05-2002 11:58a
Also, when I try to start acd.exe, it gives me "BLF" errors for every channel.
There is some programming exist on the ksu and on the vm. Coud I reset the ksu and vm to the defaults and reprogram from the scratch? What is the procedure? Thanks again!
|
|
|
|
Joined: Nov 2003
Posts: 1,313
Member
|
Member
Joined: Nov 2003
Posts: 1,313 |
pop the compact flash card into a external reader and do a scandisk & defrag.
then pop it back into the fms card and see if it will boot up enough to get into maint mode to do a database check.
|
|
|
|
Joined: Jul 2005
Posts: 32
Member
|
OP
Member
Joined: Jul 2005
Posts: 32 |
Well, ran the scandisk, no errors and defrag'd, same thing... Should I try to restore vm to default from defaults directory?
|
|
|
|
Joined: Dec 2005
Posts: 170
Member
|
Member
Joined: Dec 2005
Posts: 170 |
turn on the piano key #4, it is the one on the top of the card, push it to the right and reboot the card. it will come up to the utlity menu. check for database errors.
|
|
|
|
Joined: Jul 2005
Posts: 32
Member
|
OP
Member
Joined: Jul 2005
Posts: 32 |
after turning the piano key#4 (as well as 3) the system boots into the dos prompt and can be accessible by vt100. What should I do next?
|
|
|
|
Joined: Jul 2005
Posts: 32
Member
|
OP
Member
Joined: Jul 2005
Posts: 32 |
that's what i'm actually getting for each channel: BLF test fail channel 5 <<QSTAT>> 02 0000000000*0000000000*0000000000*0000000000 * <<QSTAT>> 02 0000000000*0000000000*0000000000*0000000000*
|
|
|
|
Joined: Dec 2005
Posts: 170
Member
|
Member
Joined: Dec 2005
Posts: 170 |
press 2 for repair database errors, and what procedure did u do when defraging the hard drive.
|
|
|
Forums84
Topics94,309
Posts638,906
Members49,771
|
Most Online5,661 May 23rd, 2018
|
|
0 members (),
132
guests, and
144
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
|
|