|
Joined: Nov 2006
Posts: 70
Member
|
OP
Member
Joined: Nov 2006
Posts: 70 |
Hello.
I have taken over a job on a previously setup system. Here is the situation:
Fax machine extensions( all connected to SLI cards in a idcs 500 R1 system) are automatically dial 9 as soon as they go off-hook.
However, I need to change this to dial a particular trunk group instead of dialing 9.
I would normally go into MMC 306 Hot line and assign the trunk number(to the fax extension) as well as go into MMC 502 and change the off-hook selection timer to 0 or 1 seconds for that extension. So it would immediately assess the trunk group as soon as it went off-hook.
However, this is apparently being done by a different method and I can't figure out how these SLI lines are automatically dialing 9 without the use of MMC 306.
Please let me know if you have any ideas.
Thanks.
|
|
|
Visit Atcom to get started with your new business VoIP phone system ASAP
Turn up is quick, painless, and can often be done same day.
Let us show you how to do VoIP right, resulting in crystal clear call quality and easy-to-use features that make everyone happy!
Proudly serving Canada from coast to coast.
|
|
|
Joined: Sep 2005
Posts: 690
Member
|
Member
Joined: Sep 2005
Posts: 690 |
Well your right about MMC 306. It is also the only place in the Samsung system where you can assign an off hook select. I would check the fax machines to see if they have some sort of off hook dial 9 programing. Also have you tried a butset connected directly to one of the analog ports. If you go off hook on your butset does it put you on a trunk or do you have intercom dial tone? This would rule out the Samsung as the culprit.
|
|
|
|
Joined: Sep 2001
Posts: 2,330 Likes: 7
Moderator-Executone-Isoetec, Samsung
|
Moderator-Executone-Isoetec, Samsung
Joined: Sep 2001
Posts: 2,330 Likes: 7 |
Check mmc 307 off hook select.
|
|
|
|
Joined: Jul 2006
Posts: 99
Member
|
Member
Joined: Jul 2006
Posts: 99 |
Have you checked to see if they are using LCR Route tables & Modify Digit Table. (MMC 712-713)
-Tom-
|
|
|
|
Joined: Oct 2006
Posts: 140
Member
|
Member
Joined: Oct 2006
Posts: 140 |
Yah, I was thinking the same as Connexions1. If its not hotline, then it would be a mod table. If its neither, then it MUST be something on the user side outside of Samsung.
|
|
|
|
Joined: Nov 2006
Posts: 70
Member
|
OP
Member
Joined: Nov 2006
Posts: 70 |
Hi.
I have not yet been back to the site to test out the regular phone on the line to rule out the fax machine itself doing the trunk selection.
I have the system setup in MMC 724 dial number plan under " features" to set LCR to " 9"
So all phone which dial 9 to get outside line will automatically be going through the LCR process to select the best trunk for the area code dial(setup in the LCR tables mentioned) .
However, these fax machines are automatically grabbing outside lines without dialing 9 and without having a hot line setup to dial 9 for the extension.
There fax machines are connected to SLI lines in the system and I can dial from other phones in the office.
Perhaps this dialing might be happening on the fax machine itself because I can't think of any other way the Samsung system can link a SLI line to a trunk group without doing a off-hook trunk selection in MMC 306?
Thanks for your help guys. I will try to keep you updated when(or if) I find out how this is occurring in this setup.
|
|
|
|
Joined: Sep 2001
Posts: 2,330 Likes: 7
Moderator-Executone-Isoetec, Samsung
|
Moderator-Executone-Isoetec, Samsung
Joined: Sep 2001
Posts: 2,330 Likes: 7 |
Again, Check mmc 307 I'd bet it's set up to dial the 9.
|
|
|
|
Joined: Nov 2006
Posts: 70
Member
|
OP
Member
Joined: Nov 2006
Posts: 70 |
Originally posted by pvj: Again, Check mmc 307 I'd bet it's set up to dial the 9. Thank you for the suggestions. May I ask what is MMC 307 ? My PCMMC software nor my tech manual shows that program listed. Do you mean MMC 306 Hot Line/off hook selection ? Perhaps in Canada your Hot line/ off hook selection program is called MMC 307 instead of MMC 306? Thanks.
|
|
|
|
Joined: Sep 2006
Posts: 530
Member
|
Member
Joined: Sep 2006
Posts: 530 |
307 does not show in my OfficeServ Manager but if you try programming from a phone it is there.
306 is Hot Line and 307 is Off Hook Select. You need to use 307. I tested it here in my office on an iDCS 100 R1.
|
|
|
|
Joined: Nov 2006
Posts: 70
Member
|
OP
Member
Joined: Nov 2006
Posts: 70 |
Originally posted by Cracker: 307 does not show in my OfficeServ Manager but if you try programming from a phone it is there. You need to use 307. I tested it here in my office on an iDCS 100 R1. 306 is Hot Line and 307 is Off Hook Select and these are 2 separate programs that do the exact same thing? My apologizes to pvj, I thought you were referring to MMC 306 hotline but it name labeled slightly different in the Canadian version vs US version. I am not sure why Samsung has these hidden secrete programs which are do not show up in the software or manual? Anyway, that sounds like it may be exactly what I'm looking for! I have not been to the physical site in a while, only remote access via pcmmc. So it may been a while until I can let you know how it turns out. However, I am very hopeful that the MMC 307 may be the thing I was looking for. Thanks.
|
|
|
Forums84
Topics94,299
Posts638,872
Members49,770
|
Most Online5,661 May 23rd, 2018
|
|
0 members (),
75
guests, and
324
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
|
|