atcomsystems.ca/forum Forums TDM Business Telephone Systems NEC Telephones & Systems Anyone Good With 2000IVS SMDR?

Site 8

COMMAND=08
08>040:0-
08>053:1-
08>368:1-
08>370:1-
08>377:0-
08>378:0-
08>379:0-
08>424:1-
08>425:1-
08>426:1-
08>463:1-

COMMAND=A703
A703>0:0-
A703>1:3-
A703>2:3-
A703>3:3-

COMMAND=A704
A704>0:00001-
A704>1:NONE-
A704>2:NONE-
A704>3:NONE-

COMMAND=A726
A726>0:0-
A726>1:1-
A726>2:1-
A726>3:1-

COMMAND=A727
A727>0:1-
A727>1:1-
A727>2:1-
A727>3:1-

COMMAND=A728
A728>0:0-
A728>1:1-
A728>2:1-
A728>3:1-

COMMAND=D000
D000>70:1-
D000>76:1-
D000>77:1-
D000>79:0-

COMMAND=D001
D001>20:2-
D001>21:0-
D001>22:0-
D001>23:1-
D001>80:4-
D001>81:0-
D001>82:3-
D001>84:1-
D001>85:0-
D001>86:0-
D001>100:0-
D001>104:0-
D001>105:0-
D001>106:0-
D001>120:0-
D001>140:0-
D001>179:0-
D001>239:0-

COMMAND=D003
D003>24:0-
D003>26:0-
D003>29:0-

COMMAND=D004
D004>55:0-
D004>56:0-

COMMAND=D016
D016>0016:1-
D016>0017:0-
D016>0021:1-
D016>0022:0-
D016>0030:1-
D016>0031:1-
D016>0032:1-
D016>0055:0-
D016>0058:1-

COMMAND=D027
D027>0000:9-
D027>0001:9-
D027>0002:9-
D027>0003:9-
D027>0004:9-
D027>0005:9-
D027>0006:9-
D027>0007:9-
D027>0008:9-
D027>0009:9-

COMMAND=D034
D034>0000:11-
D034>0001:11-
D034>0002:11-
D034>0003:11-
D034>0004:11-
D034>0005:11-
D034>0006:11-
D034>0007:11-
D034>0008:11-
D034>0009:11-

Thanks Rod, sorry so long!

couple of things,

In site 1 D016 should match what you have in say site 3.

Also in sites 3 and 5 the the CCH's pointing to the remote should be a 1.

Finally a point I missed earlier What do you have for all site in cm A8>Pointcode>

Let me also know what CCH points to where per switch.

------------------
Hot Rod

Also what revision of PBX's are they IVS2 IPS?

------------------
Hot Rod

Good Morning,

*The revisions (IVS, IVS2, IPS) are listed in the original post above.

*I've actually changed CMA703 on site 5 before from:

CMA703>0>0
CMA703>1>3
CMA703>2>3

To:

CMA703>0>0
CMA703>1>1
CMA703>2>1

However, when I made the change site 5 became an Island and couldn't connect to attached sites 1, 6, & 8.

* Site 1
CMA8>0>00002
CMA8>1>00003
CMA8>2>00004
CMA8>3>00005

Site 2
CMA8>0>00001

Site 3
CMA8>0>00001
CMA8>1>00007

Site 4
CMA8>0>00001

Site 5
CMA8>0>00001
CMA8>1>00006
CMA8>2>00008

Site 6
CMA8>0>00005

Site 7
CMA8>0>00003

Site 8
CMA8>0>00005

*As far as CMD016 being the same as sites 3 & 5, I'm a little leery making changes being that Site 1 is the Center Office, is this wrong?

Thanks for your help so far I hope this information is useful.

A8 is not correct I need the layout of CCH# points to site #. What is needed is that all point codes are defined in each switch. in command A8.

"However, when I made the change site 5 became an Island and couldn't connect to attached sites 1, 6, & 8."
Do you mean no calls or no records. If no calls I ve seen this before and what fixed that was a reset at the main.

"*As far as CMD016 being the same as sites 3 & 5, I'm a little leery making changes being that Site 1 is the Center Office, is this wrong?"
With D016 set in sites 3&5 that way they are requesting call records that the main is not.



------------------
Hot Rod

Oops sorry I typed them in backwards:

*Site 1
CMA8>00002>0
CMA8>00003>1
CMA8>00004>2
CMA8>00005>3

Site 2
CMA8>00001>0

Site 3
CMA8>00001>0
CMA8>00007>1

Site 4
CMA8>00001>0

Site 5
CMA8>00001>0
CMA8>00006>1
CMA8>00008>2

Site 6
CMA8>00005>0

Site 7
CMA8>00003>0

Site 8
CMA8>00005>0

*"However, when I made the change site 5 became an Island and couldn't connect to attached sites 1, 6, & 8."
Do you mean no calls or no records. If no calls I ve seen this before and what fixed that was a reset at the main.

When I changes the two 3's to 1's I could not pick up my phone (Site 5) and direct 4 digit dial any other building.

*That makes sense about CMD016, what changes to which sites would you recommend I try? (The CMD016 command settings for all sites involved are listed in previous messages)

A8 should look like this...

Site 1 A8>XXXXX>CCH
00001>NONE
00002>0
00003>1
00004>2
00005>3
00006>3
00007>1
00008>3

Site 2 A8
00001>0
00002>None
00003>0
00004>0
00005>0
00006>0
00007>0
00008>0

Site 3 A8
00001>0
00002>0
00003>NONE
00004>0
00005>0
00006>0
00007>1
00008>0

Site 4 A8
00001>0
00002>0
00003>0
00004>NONE
00005>0
00006>0
00007>0
00008>0

Site 5 A8
00001>0
00002>0
00003>0
00004>0
00005>NONE
00006>1
00007>0
00008>2

Site 6 A8
00001>0
00002>0
00003>0
00004>0
00005>0
00006>NONE
00007>0
00008>0

Site 7 A8
00001>0
00002>0
00003>0
00004>0
00005>0
00006>0
00007>NONE
00008>0

Site 8 A8
00001>0
00002>0
00003>0
00004>0
00005>0
00006>0
00007>0
00008>NONE

As far as D016 Have site 1 look like the others they are reporting more than the main.

------------------
Hot Rod

*Ok I adjusted every switch to the exact CMA8 settings you provided.

*Next I made our Main Site (Site 1) similar to the other Sites for the CMD016 settings. I changed 0021, 0030, 0031, 0032, and 0058 all from a 0 to a 1.

*I also changed on Site 5 CMA703>1 &2 from a 3 to a 1. As soon as I made the change and dialed Sites 1, 6, and 8, I get restricted in the display and I have to grab an outside line and place a local call to talk to those sites. Went in through cat mode and reset both back to a 3, had to do a hard reset though to accept the changes and reconnect.

*Still have the same issues as mentioned in the first post… but I think the first two changes you suggested were good moves.

Any other suggestions, thanks for these suggestions so far!

PS. When I changed the CMA703 settings on Site 5 I changed the 3 to a 1 for Site 8 first and I seemed ok. Once I changed the CMA703 for Site 6 that's when I lost connection to Sites 1, 6, and 8.

Sorry It took so long to reply,

Did you try a reset when you made the changes to site 5. Or did you just set them back to a 3 and reset?

If you can I would leave A703>2>1 this should allow you to get records for site 8

Sites 5,6 & 7 may have a HW problem chips on the AP00 card what are they?
SC-xxxx
and CX.X

------------------
Hot Rod