web statisticsweb stats

Business Phone Systems

Previous Thread
Next Thread
Print Thread
Rate Thread
Page 1 of 2 1 2
Joined: Feb 2004
Posts: 273
Member
OP Offline
Member
Joined: Feb 2004
Posts: 273
have MICS 5.0 with polycom sound station 2 working on an older ATA ,can make and receive calls fine but unable to do conference calls

Nortel Phone System Service
VoIP Demo

Nortel Phone System Service in Canada


Do you need a Nortel Phone System technician or specific Nortel parts?
Atcom to the rescue! Our telephone techs have qualified experience servicing and troubleshooting Nortel CICS, MICS, & BCM telephone systems.
Service in Canada from sea to sea.

Joined: Jan 2013
Posts: 36
Member
Offline
Member
Joined: Jan 2013
Posts: 36
At what stage does it fail? If you establish the first call, can you press the Recall button & then 2, to get internal dial tone again?

Joined: Dec 2003
Posts: 2,086
Former Moderator-Nortel
Offline
Former Moderator-Nortel
Joined: Dec 2003
Posts: 2,086
Does the DN for the polycom have 2 intercoms programmed?

Make or answer 1st call.
Press LINK + 2 -puts call on hold.
Make or answer 2nd call.
Press LINK + 3 - this completes the conf call.


If CON is the opposite of PRO
Then what is the opposite of Progress?
Joined: Feb 2004
Posts: 273
Member
OP Offline
Member
Joined: Feb 2004
Posts: 273
yes I have 2 icm's programmed on unit
This unit is wireless to the base,
there is no link btn or does it appear in the led screen (not on site at moment)
I have been making the first call, then pressing conference btn unable to get second dialtone to call out

Joined: Jan 2013
Posts: 36
Member
Offline
Member
Joined: Jan 2013
Posts: 36
Ha, I'm caught out again! In Australia we call it the Recall button, you obviously don't. I've never heard it referred to as a LINK button.

Joined: Feb 2004
Posts: 273
Member
OP Offline
Member
Joined: Feb 2004
Posts: 273
The flash is set at 600, I tried lower settings but didn't make any dif

Joined: Jan 2013
Posts: 36
Member
Offline
Member
Joined: Jan 2013
Posts: 36
Looking at the manual. I think you need to press Conference, then 2, to get the internal dial tone back.

In other words the same as NTlayoff's post, except for substituting CONFERENCE for LINK.

Also the Flash Timing should probably be 100ms, but depends on your CO's.

Joined: Dec 2003
Posts: 2,086
Former Moderator-Nortel
Offline
Former Moderator-Nortel
Joined: Dec 2003
Posts: 2,086
Originally Posted by kevinlms
Looking at the manual. I think you need to press Conference, then 2, to get the internal dial tone back.
In other words the same as NTlayoff's post, except for substituting CONFERENCE for LINK.
Also the Flash Timing should probably be 100ms, but depends on your CO's.

Kevin - Are you looking at an OPTION manual?


If CON is the opposite of PRO
Then what is the opposite of Progress?
Joined: Jan 2013
Posts: 36
Member
Offline
Member
Joined: Jan 2013
Posts: 36
No, the Polycom Manual

https://support.polycom.com/global/...oundstation2_with_display_user_guide.pdf

Plus this from what we call an SLT manual for the ATA for an CICS or MICS.

Note your labelling is apparently link, instead of Recall.

Conference

The Conference feature lets you establish a conference call between yourself
and two other parties.
1. Make or answer the first call.
2. Press Recall 2 to put the call on hold.
3. Make the second call.
4. Press Recall *3 to establish the conference.
If the second person you call is busy, or if there is no answer:
1. Hang up the handset.
2. Lift the handset again.
3. Press Recall 2 to return to the first call.
To place the conference on hold:
1. Press Recall 2.
The other two parties in the conference remain connected.
To rejoin a held conference:
1. Press Recall 2.
To split a conference into two separate calls:
1. Press Recall #3.
To alternate between the two separate calls:
1. Press Recall 2.
To reconnect the conference:
1. Press Recall *3.
To disconnect one party:
1. Press Recall #3 to put the one of the parties on hold.
2. If you are not connected to the party that you want to disconnect, press
Recall 2.
3. Hang up the handset.
4. Lift the handset again.
5. Press Recall 2.

You are reconnected to the call on hold.


FWIW, I've never worked on an Option.

Joined: Jun 2006
Posts: 8,732
Likes: 2
Moderator-Nortel, Computers, General
*****
Offline
Moderator-Nortel, Computers, General
*****
Joined: Jun 2006
Posts: 8,732
Likes: 2
The Conference feature lets you establish a conference call between yourself
and two other parties.
1. Make or answer the first call.
2. Press (Recall, Link or Flash...all the same thing) 2 to put the call on hold.
3. Make the second call.
4. Press Recall *3 to establish the conference.

NOTE: You'll get dial tone THE SAME WAY as you made the 1st call. In other words, you have to have the unit set up on an ata with Line Pool (A) or whatever as the prime line. When you go off-hook, you'll get a line, same thing 2nd time. NOTE: your lines must be in a pool.
If the prime is set as intercom, then you'll have to do F64x to get a line. Again, same for 2nd call.
If you don't understand, call me: 819-564-2303

Last edited by MooreTel; 09/20/16 04:21 PM.

Scientists say that the universe is made up of Protons, Neutron & Electrons. They forgot "Morons".
Dave. (CTUB) Canadian Techs Use Bix!
Page 1 of 2 1 2

Moderated by  MooreTel 

Link Copied to Clipboard
Forum Statistics
Forums84
Topics94,333
Posts639,024
Members49,785
Most Online5,661
May 23rd, 2018
Popular Topics(Views)
213,512 Shoretel
190,827 CTX100 install
189,277 1a2 system
Newest Members
Micheal C, etel, AVO-IT, wierderal, Rupert
49,784 Registered Users
Top Posters(30 Days)
Rupert 10
tim10 9
Toner 7
Yoda 6
dexman 5
Who's Online Now
0 members (), 150 guests, and 91 robots.
Key: Admin, Global Mod, Mod
Contact Us | Sponsored by Atcom: One of the best VoIP Phone Canada Suppliers for your business telephone system!| Terms of Service

Sundance Communications is not affiliated with any of the above manufacturers. Sundance Phone System Forums - VOIP & Cloud Phone Help
©Copyright Sundance Communications 1998-2024
Powered by UBB.threads™ PHP Forum Software 7.7.5