MP20s Boot version V0.50 (2013.01.14)
SDRAM : 128 MB (0x80000000)
EEPROM : 12KByte
CabinetID : MP20S
SD Driver Clk : 12MHz
Hit 'Q' or 'q' key to stop autoboot: 0
NAND Protection is disabled ...!!!
+yCard_Read_File, destPtr(0x81000000)
Valid MMC FW flag
+InitializeMmcController
Eata_init_ata16()
Eata_detect_ata16 : Eata ata16v2_identify.
Eata_detect_ata16 : Detect Sain Eata device.
===============================
General Configuration: 04ca
serial number: 20000801
firmware revision: VER 1.23
model: ATA16V2 M2C4-SAIN MMCSM VER 0.12
capabilities (49): 0f00
capabilities (50): 0000
flags (53): 0003
dma (63): 0407
pio (64): 0003
===============================
... Card is formatted with FAT16
... f->filename = startup.ini
... f->filesize = 288
... filetime: 2016-7-21, 14:37:30
... f->filename = ms2sv125.pkg
... f->filesize = 2025025
... filetime: 2016-7-21, 14:36:18
Reading a file from MMC card... Done
+yCard_Read_File, destPtr(0x81600000)
... f->filename = startup.ini
... f->filesize = 288
... filetime: 2016-7-21, 14:37:30
... f->filename = cs2sv495.pkg
... f->filesize = 1518288
... filetime: 2016-7-21, 14:36:0
Reading a file from MMC card... Done
+yCard_Read_File, destPtr(0x82000000)
... f->filename = startup.ini
... f->filesize = 288
... filetime: 2016-7-21, 14:37:30
... f->filename = rd2sv495.pkg
... f->filesize = 6959038
... filetime: 2016-7-21, 14:36:36
Reading a file from MMC card... Done
Downloading MSP Image from 0x81000000 ...
code_offset=0x80
code_base=800000
data_offset=1d6ff0
code_size=1d6f70
data_base=9d6f70
data_size=114
zeroinit_base=9d7084
prog_entry=100
AIFHEADER:
BL_DecompressCode=e1a00000
BL_SelfRelocCode=e1a00000
BL_DbgInitZeroInit=eb00000c
EntryPointOffset=ff800100
ProgramExitInstr=ef000011
ImageReadOnlySize=1d6f70
ImageReadWriteSize=114
ImageDebugSize=2444
ImageZeroInitSize=113ac
ImageDebugType=224c1
ImageBase=800000
WorkSpace=0
AddressMode=20
DataBase=0
FirstFatOffset=1d9548
Reserved2=1da244
DebugInitInstr=e1a00000
ZeroInitCode[0]=e04ec00f
<setup_memory_tags> bd->sdram_bank : 1
Booting ARM0 (MSP) at 0x00000100 ...
Booting ARM1 (CSP) at 0x81600000 ...
Linux version 2.6.13-rtl (tacoon@mp10) (gcc version 3.3.2) #241 Wed Nov 25 16:36:42 KST 2015
CPU: ARM920Tid(wb) [41129200] revision 0 (ARMv4T)
Machine: ARM-M825xx2 Comcerto
Memory policy: ECC disabled, Data cache writeback
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
CPU0: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
Built 1 zonelists
Kernel command line: console=ttyS0,38400 root=/dev/ram0 rw initrd=0x82000000,25M ramdisk=81920 ip=10.0.0.2:10.0.0.10:10.0.0.1:255.255.255.0::eth0:off mem=128M
PID hash table entries: 1024 (order: 10, 16384 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 128MB = 128MB total
Memory: 100736KB available (2523K code, 778K data, 108K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 25600K
NET: Registered protocol family 16
Comcerto PCI: init
Comcerto PCI: Comcerto device is not configured in PCI host
Verify that HBMODE_n(low) pin is high and HBBURSTEN_n(high) pin is low
On Mindspeed MH02-D370-xxx board, remove jumper JPCISLV1
SCSI subsystem initialized
SPI core: loaded version 0.2
NetWinder Floating Point Emulator V0.97 (double precision)
devfs: 2004-01-31 Richard Gooch (
[email protected])
devfs: boot_options: 0x1
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
yaffs Nov 25 2015 11:03:38 Installing.
Initializing Cryptographic API
Crypto engine S/W registered
Serial: 8250/16550 driver $Revision: 1.4 $ 2 ports, IRQ sharing enabled
Serial: Comcerto 16550 serial driver $Revision: 1.2 $
ttyS0 at MMIO 0x10090000 (irq = 41) is a 16550A
io scheduler noop registered
RAMDISK driver initialized: 1 RAM disks of 81920K size 1024 blocksize
loop: loaded (max 8 devices)
nbd: registered device at major 43
m825xx_ved: version 0.0.2-2.6cvs
m825xx_ved: init SMI
NFTL driver: nftlcore.c $Revision: 1.1.1.1 $, nftlmount.c $Revision: 1.1.1.1 $
NAND device: Manufacturer ID: 0x92, Chip ID: 0xf1 (Eon/Zentel/ESMT NAND 128MiB 3,3V 8-bit)
Scanning device for bad blocks
Creating 1 MTD partitions on "NAND 128MiB 3,3V 8-bit":
0x00000000-0x08000000 : "OS7100 NAND Flash partition"
SPI core: add adapter comcerto-spi
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
Disabled Privacy Extensions on device c02e1578(lo)
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
NET: Registered protocol family 4
IP-Config: Complete:
device=eth0, addr=10.0.0.2, mask=255.255.255.0, gw=10.0.0.1,
host=10.0.0.2, domain=, nis-domain=(none),
bootserver=10.0.0.10, rootserver=10.0.0.10, rootpath=
RAMDISK: Compressed image found at block 0
crc error
VFS: Mounted root (ext2 filesystem).
mount_devfs_fs(): unable to mount devfs, err: -20
Freeing init memory: 108K
Warning: unable to open an initial console.
Kernel panic - not syncing: No init found. Try passing init= option to kernel.
<7>eth0: no IPv6 routers present
