|
Joined: Dec 2007
Posts: 6,816 Likes: 20
Retired Admin
|
Retired Admin
Joined: Dec 2007
Posts: 6,816 Likes: 20 |
Originally posted by Michael Havens: Originally posted by MooreTel: [b] I thought cg=cable guy! [/b]Sorry you're mistaken, Larry=Cable Guy.
|
|
|
Visit Atcom to get started with your new business VoIP phone system ASAP
Turn up is quick, painless, and can often be done same day.
Let us show you how to do VoIP right, resulting in crystal clear call quality and easy-to-use features that make everyone happy!
Proudly serving Canada from coast to coast.
|
|
|
Joined: Dec 2007
Posts: 6,816 Likes: 20
Retired Admin
|
Retired Admin
Joined: Dec 2007
Posts: 6,816 Likes: 20 |
The customer wanted me to install a new voice/data network. The first two pictures are what it looked like before I started, and the final picture is my install. And a Close-Up After:
|
|
|
|
Joined: Jan 2005
Posts: 15,384 Likes: 13
Moderator-Vertical, Vodavi, 1A2, Outside Wire
|
Moderator-Vertical, Vodavi, 1A2, Outside Wire
Joined: Jan 2005
Posts: 15,384 Likes: 13 |
Wow, what an improvement. How come they are always willing to pay to do it right the second time?
Ed Vaughn, MBSWWYPBX
|
|
|
|
Joined: Dec 2002
Posts: 9,428 Likes: 1
Member
|
Member
Joined: Dec 2002
Posts: 9,428 Likes: 1 |
What is that wire coming out of the wall just above the electrical outlet? I think I spot the phone jack from your other post
Jeff Moss Moss Communications Computer Repair-Networking-Cabling MBSWWYPBX, JGAE
|
|
|
|
Joined: Dec 2007
Posts: 6,816 Likes: 20
Retired Admin
|
Retired Admin
Joined: Dec 2007
Posts: 6,816 Likes: 20 |
Originally posted by jeffmoss26: What is that wire coming out of the wall just above the electrical outlet? I think I spot the phone jack from your other post Correct Jeff. It's the same location. I had intended to run all the cable inside the wall, however I discovered that the at one time the wall had a window right there...it was just "framed in". Thus the little sticks of raceway to work around the blockages. This bid job was site unseen and 250 miles out of town. "Take what you think you might need."
|
|
|
|
Joined: Jun 2008
Posts: 35
Member
|
Member
Joined: Jun 2008
Posts: 35 |
I would have used a long flex bit through the mudring below and through a larger hole behind the rack for the runs that go up. Or a new mudring can be cut in 6" above or below the blocking to allow a standard auger access to drill through. Cap it off with a blank plate or the owner can have the hole patched. Looks better IMHO than a raceway going halfway up a wall.
|
|
|
|
Joined: Dec 2002
Posts: 9,428 Likes: 1
Member
|
Member
Joined: Dec 2002
Posts: 9,428 Likes: 1 |
This is what I was curious about...
Jeff Moss Moss Communications Computer Repair-Networking-Cabling MBSWWYPBX, JGAE
|
|
|
|
Joined: Dec 2007
Posts: 6,816 Likes: 20
Retired Admin
|
Retired Admin
Joined: Dec 2007
Posts: 6,816 Likes: 20 |
Yes, that was "Customer Installed"
|
|
|
|
Joined: Nov 2010
Posts: 30
Member
|
Member
Joined: Nov 2010
Posts: 30 |
Here's 3 of a switch I completed this week. Just need to heatshrink the end and done. But in reality, higherups called for braiding the cables, which I have no pictures of. I hate braiding cables. Also, please note that that mx80 is supported by a 0u shelf on the bottom, only able to secure with two screws on the top. Bottom holes were covered/occupied by shelf. there's another relay rack in back of the front relay rack supporting the back end of the equipment.
|
|
|
|
Joined: Dec 2007
Posts: 6,816 Likes: 20
Retired Admin
|
Retired Admin
Joined: Dec 2007
Posts: 6,816 Likes: 20 |
Good job Badcable. Here is another picture of how it should be done:
|
|
|
Forums84
Topics94,424
Posts639,481
Members49,821
|
Most Online5,661 May 23rd, 2018
|
|
1 members (Robert Stuart),
252
guests, and
29
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
|
|