atcomsystems.ca/forum Forums Other TDM Phone Systems Telrad Telephones & Systems telrad 818 start up problem, HELP !

NO everything is working fine probably!!

You have to link up with your pcp programing software (use pcp sub5.10). you have to make a cable to link up with the mpd card to your computer. this will allow you to see what cards are working and to programing system. here's the pin out for that cable. go to radio shack and get a 9 pin female comport cable connector (for compuet end) and also a 8-pin module pulg (for mpd end). mpd pin 4 goes to pin 5 on 9 pin com port 5 goes to 3, 6 goes to 2.

then link up, in pcp software go to connect direct to system select the com port on your computer and connect at 4800 baud rate.

The jack side is standard but on the break-out side you skip the third pair on each port. So you would have a total of 8 stations on the ELD card with a empty pair between them. you can also pair the ports up and run 16 off one ELD but we won't get into that just yet.
Let me know when you are going out there again and I will try to be in the office so we can get this taken care of.

We are going back out there Tuesday morning.

This thing is got us fit to be tied.

I know it's something stupid were doing wrong but I we have no experience with the TELRAD SYSTEMS and we just can't see what it is.

We wired it the way it said in the manual.
Once we realized that it was not wired like the standard system, such as the Panosonic's etc...




[This message has been edited by fonetec (edited August 10, 2003).]

This system is a little more diffult than other pbx's. You might have to dn the station. the 1st port on the eld card could be programed to be any ext. but it is usally 20 or 220 or 200. Put a display set on the 1st port on the eld card( this is the white/blue and orange pair on the 25 pair cut down) do at at the MDF. than tpye on the dail pad #- the ext number- than # again.


Hope this might help for monday.

Fonetec
You can leave off the first #. When you plug in a phone with 2 DN's programmed on the same port the phone will scan (MSG DND MUTE SPKR) this is asking for its DN. Enter the ext number (i.e. 200) then #.
Also Tech assistance is just a phone call away. See my profile for number.


[This message has been edited by SSPhone (edited August 11, 2003).]

Put the 1st # in this will clear anything you have already or someonelse might have put in.

I will be in the office on Tues. morning.

DTMF thank you

We will call you 1st thing.

SSphone
Thanks, but are sure you want us to call
(hehe)

[This message has been edited by fonetec (edited August 11, 2003).]

Dtmf sent me the software for the 128 but my firewall changed the extensions to:

DKEYBX.zl3
INSTALL.zl3
SBU5.zl9
UDCLIP.zl9
UPDN.zl9

Can someone please tell me what the extensions are suppose to be so I can change them back or resend this program to:

[email protected]

or put the files in a folder and ZIP it and then send it to me.

If the program is in a file and zipped my firewall will not change the extensions.

Or are all the extensions suppose to be:

.exe

Tanx

[This message has been edited by fonetec (edited August 11, 2003).]

[This message has been edited by fonetec (edited August 11, 2003).]

IT'S RUNNING !!!!!

DTMF thank you, so much I will call and get your address so I can send you something !

Same goes for you SSPhone.

DTMF I still need that software we were talking about on the phone.

If you would rather send it to my other email address you can and I can download it from there:

[email protected]

Thanks Everyone For The Help !!!

[This message has been edited by fonetec (edited August 12, 2003).]