Outgoing caller id on CIC's with PRI

Support Service-Disabled Veterans!
Discount software from Direct Deals

Print Thread

Rate Thread

Outgoing caller id on CIC's with PRI #122083 10/06/04 12:35 PM
Joined: Nov 2001 Posts: 81 Irvine, CA Mark Smith Member
Mark Smith Member Joined: Nov 2001 Posts: 81 Irvine, CA	Is is possible for the individual DID's to be sent out from the pbx. I have OLI on the sets but the carrier says he is not seeing my caller id. Here is the PRI trap from the carrier - am i missing a setting or can this not be done? They are not seeing a calling DN from my pbx Event 6 04/10/06 16:02:29 TEI 0 TRIG 08 Q.931 Call Control Message Call Reference Value Orig 16 M 05 Message Type SETUP I 04 Bearer Capability Length = 3 80 Coding Standard CCITT Info Transfer Cap. Speech 90 Transfer Mode Circuit Transfer Rate 64 kbit/s A2 Layer 1 Protocol G.711 u-law I 18 Channel Identification Length = 3 A1 Interface ID Implicitly Defined Interface Type Primary Preferred/Exclusive Preferred D Channel Indicator Not D Channel Channel Selection As Indicated 83 Coding Standard CCITT Coding Type Number Channel Type B Channel 8B Channel Number 11 I 70 Called Party Number Length = 12 80 Type of Number Unknown Type Numbering Plan Unknown Numbering Plan Number 19495551212 Raw Hex Data 08 02 00 10 05 04 03 80 90 A2 18 03 A1 83 8B 70 0C 80 31 39 34 39 32 36 35 32 31 39 34

Nortel Phone System Service

Nortel Phone System Service in Canada

Do you need a Nortel Phone System technician or specific Nortel parts?
Atcom to the rescue! Our telephone techs have qualified experience servicing and troubleshooting Nortel CICS, MICS, & BCM telephone systems.
Service in Canada from sea to sea.

Re: Outgoing caller id on CIC's with PRI #122084 10/06/04 02:58 PM
Joined: Aug 2004 Posts: 1,705 Likes: 36 Calgary, AB, Canada Toner Admin
Toner Admin Joined: Aug 2004 Posts: 1,705 Likes: 36 Calgary, AB, Canada	What sort of PBX are you talking about? Option 11, SL-1, or do you mean a Norstar? Whoops, I see you answered that question in your Topic Heading. I'm afraid I don't know whether Norstar is capable of sending outgoing CID. I can't think of where you'd input the number in programming off the top of my head. [This message has been edited by Toner (edited October 06, 2004).] Looking for a VoIP Phone Canada provider? Put Atcom's valuable VoIP expertise to work for your business today!

Re: Outgoing caller id on CIC's with PRI #122085 10/07/04 03:20 PM
Joined: Mar 2002 Posts: 3,630 Denver Z-man Moderator-Avaya, Nortel
Z-man Moderator-Avaya, Nortel Joined: Mar 2002 Posts: 3,630 Denver	you mean on a MICS, right? You can't do T-1 on a CICS. Z-man Avaya SME Authorized Partner www.omniofficetech.com

Re: Outgoing caller id on CIC's with PRI #122086 01/12/05 08:58 AM
Joined: Jan 2005 Posts: 7 Tucson, AZ, USA rflores Member
rflores Member Joined: Jan 2005 Posts: 7 Tucson, AZ, USA	I just did a install on a MICS 6.1 with a PRI. All I did to get CLID to work was made sure the LEC was sending the correct number of digits and set my OLI on the sets with there DID numbers.

Re: Outgoing caller id on CIC's with PRI #122087 01/17/05 02:59 AM
Joined: Nov 2003 Posts: 1,310 Miami, FL Danny_Ocean Member
Danny_Ocean Member Joined: Nov 2003 Posts: 1,310 Miami, FL	FWIW: The Telco's equipment might not be compatible. I set up two (nearly) identical systems (MICS w/PRI) within the same geographic area. One client, using BellSouth could not block or manipulate their out-bound CID. The other client, using a local carrier (USLEC) had no problems doing so. D. Ocean Miami, FLA D. Ocean Miami, FL