|
Joined: May 2008
Posts: 8
Member
|
Member
Joined: May 2008
Posts: 8 |
During the process of making a 2pair cable longer i think 2 wires touched and now the phone is dead (this extension only)all other phones on the system are working.I noticed 3 or 4 small glass fuses back on control panel,could one of these be blown or does anyone have any ideas?Thanks in advance for your help.
Regards Paul
|
|
|
Visit Atcom to get started with your new business VoIP phone system ASAP
Turn up is quick, painless, and can often be done same day.
Let us show you how to do VoIP right, resulting in crystal clear call quality and easy-to-use features that make everyone happy!
Proudly serving Canada from coast to coast.
|
|
|
Joined: Jan 2004
Posts: 6,648
RIP Moderator-Nisuko-Tie, General
|
RIP Moderator-Nisuko-Tie, General
Joined: Jan 2004
Posts: 6,648 |
have you tried powering down for 10 minutes so and then powering up? I don't think the fuses have anything to do with it but they are easy enough to check since it happened while making the cord have you verified that the cord is good ?
Skip ------------------------------------
Serving SW and West central Fl since 1984
|
|
|
|
Joined: May 2008
Posts: 8
Member
|
Member
Joined: May 2008
Posts: 8 |
Thanks for the quick reply,i replaced the wall outlet onto the original cable and still the same,i will try powering it down in the morning.it is 1:20am now in dublin so i have left the place till tomorrow.
Thanks again Paul
|
|
|
|
Joined: May 2008
Posts: 8
Member
|
Member
Joined: May 2008
Posts: 8 |
I tried the powering down and back up but still no joy,anymore ideas would be very welcome?
Regards Paul
|
|
|
|
Joined: Jan 2004
Posts: 6,648
RIP Moderator-Nisuko-Tie, General
|
RIP Moderator-Nisuko-Tie, General
Joined: Jan 2004
Posts: 6,648 |
you need to start at the system and verify there is nothing there could be you blew the port , hooking a phone up directly will tell that
you also could go into programing and take a look at the port
Skip ------------------------------------
Serving SW and West central Fl since 1984
|
|
|
|
Joined: May 2008
Posts: 8
Member
|
Member
Joined: May 2008
Posts: 8 |
Can i find a service manual anywhere?
Regards Paul
|
|
|
|
Joined: May 2008
Posts: 8
Member
|
Member
Joined: May 2008
Posts: 8 |
Hi Skip,
I tested both pairs in the outlet socket and i am getting 24 volts on both pairs,now i am confused,would this mean the port is ok?
Cheers
Paul
|
|
|
|
Joined: Jan 2004
Posts: 6,648
RIP Moderator-Nisuko-Tie, General
|
RIP Moderator-Nisuko-Tie, General
Joined: Jan 2004
Posts: 6,648 |
I don't recall the voltages , Ive never been real keen on testing that way ,true test to me is a phone comes up .
have you tried reversing polarity on the second pair?
some of the early tie /Nitusko stuff was polarity sensitive
Skip ------------------------------------
Serving SW and West central Fl since 1984
|
|
|
|
Joined: May 2008
Posts: 8
Member
|
Member
Joined: May 2008
Posts: 8 |
it was already reversed when i went to it and it was working
|
|
|
|
Joined: Jan 2004
Posts: 6,648
RIP Moderator-Nisuko-Tie, General
|
RIP Moderator-Nisuko-Tie, General
Joined: Jan 2004
Posts: 6,648 |
Originally posted by paulduffy72: it was already reversed when i went to it and it was working so did you leave it reversed or put it back correctly? I would try reversing however its wired now . It wont hurt anything
Skip ------------------------------------
Serving SW and West central Fl since 1984
|
|
|
|
Joined: May 2008
Posts: 8
Member
|
Member
Joined: May 2008
Posts: 8 |
|
|
|
|
Joined: May 2008
Posts: 8
Member
|
Member
Joined: May 2008
Posts: 8 |
Hi Skip,
I reversed the polarity on both pairs and now is working perfectly,this is confusing because i checked my original diagram for the colours before i touched it, thanks for all your help.
Paul
|
|
|
|
Joined: Jan 2004
Posts: 6,648
RIP Moderator-Nisuko-Tie, General
|
RIP Moderator-Nisuko-Tie, General
Joined: Jan 2004
Posts: 6,648 |
:thumb:
glad you got it , thanks for letting us know
Skip ------------------------------------
Serving SW and West central Fl since 1984
|
|
|
|
Joined: May 2010
Posts: 1
Member
|
Member
Joined: May 2010
Posts: 1 |
Hi,
recently moved office and took TX system with and re-installed, everything working fine except adding the existing external answering machine.Having only intermittent success (machine takes first message then fails to work.
Any advise would be appreciated.
I have been also looking for a manual on-line that illustrates wiring??
Thanks and regards,
Conor
|
|
|
|
Joined: Jan 2004
Posts: 6,648
RIP Moderator-Nisuko-Tie, General
|
RIP Moderator-Nisuko-Tie, General
Joined: Jan 2004
Posts: 6,648 |
if it takes one message and then stops then I would suspect the machine put a SLT in place of the machine or parallel to it and make some test calls
In the future its better to start a new thread with a new question rather than tacking it on to a 2 year old one
for a manual try clicking on the manuals link at the top of the page here
Skip ------------------------------------
Serving SW and West central Fl since 1984
|
|
|
Forums84
Topics94,393
Posts639,301
Members49,804
|
Most Online5,661 May 23rd, 2018
|
|
|
|