Project 1A2: Phase I complete.

Products from our Sponsors

Print Thread

Rate Thread

Page 14 of 14

1

2

…

12

13

14

Re: Project 1A2: Phase I complete. #484979 11/08/07 07:23 AM
Joined: Sep 2007 Posts: 741 Missouri Matt1964 Member
Matt1964 Member Joined: Sep 2007 Posts: 741 Missouri	I'll grab some in a bit - I lowered the resolution on my camera and now am able to send them to my email OK. Check back in about an hour or so.

Atcom VoIP Phones

Best VoIP Phones Canada

Visit Atcom to get started with your new business VoIP phone system ASAP
Turn up is quick, painless, and can often be done same day.
Let us show you how to do VoIP right, resulting in crystal clear call quality and easy-to-use features that make everyone happy!
Proudly serving Canada from coast to coast.

Re: Project 1A2: Phase I complete. #484980 11/08/07 10:40 AM
Joined: Sep 2007 Posts: 741 Missouri Matt1964 Member
Matt1964 Member Joined: Sep 2007 Posts: 741 Missouri	Here ya go. In some pics you can see a 3 pair coming up the bottom of the board - ignore it; it's my temporary CO feed lines. Also I have to redo the rack mount phone, I want to run the cable behind the backboard; unforunately there are 2 2x4's to drill through above the backboard; and I need a special drill to get to/through them (hole hawg)? Don't remember it's name. Anyway it's a drill with a 90 degree angle on the chuck, plumbers are coming tomorrow so I'll borrow theirs. Need to straighten out my jumper clips too. I had them all perfect once, but troubleshooting kinda threw them helter skelter. And I have a whole lot of hole filling and painting on the backboard to do. Most of the stuff has been installed and moved at least 2 times. I have another sheet of plywood ... I'm half tempted to do it all over again, now that I know where I want everything. But only half tempted. https://img180.imageshack.us/img180/5889/11080717121ia7.jpg https://img216.imageshack.us/img216/352/11080717122my8.jpg https://img219.imageshack.us/img219/1347/11080717123ab8.jpg https://img180.imageshack.us/img180/9663/11080717131ij4.jpg https://img219.imageshack.us/img219/8388/11080717132ck1.jpg https://img180.imageshack.us/img180/5430/11080717133pn6.jpg https://img219.imageshack.us/img219/9052/11080717141wq3.jpg https://img219.imageshack.us/img219/1659/11080717151pv7.jpg https://img251.imageshack.us/img251/6299/11080717152jt0.jpg https://img219.imageshack.us/img219/4325/11080717153ic7.jpg https://img180.imageshack.us/img180/6563/11080717154xw0.jpg https://img180.imageshack.us/img180/1120/11080717161mu2.jpg https://img219.imageshack.us/img219/9748/11080717162go0.jpg

Re: Project 1A2: Phase I complete. #484981 11/08/07 11:26 AM
Joined: Dec 2002 Posts: 9,429 Likes: 3 Beachwood jeffmoss26 Member
jeffmoss26 Member Joined: Dec 2002 Posts: 9,429 Likes: 3 Beachwood	Looks good! Where did you get those telco gray cable ties? Jeff Moss Moss Communications Computer Repair-Networking-Cabling MBSWWYPBX, JGAE

Re: Project 1A2: Phase I complete. #484982 11/08/07 12:25 PM
Joined: Sep 2007 Posts: 741 Missouri Matt1964 Member
Matt1964 Member Joined: Sep 2007 Posts: 741 Missouri	Well, I'll let the guy who supplied 'em chime in if he wants.

Re: Project 1A2: Phase I complete. #484983 11/08/07 12:45 PM
Joined: Jan 2005 Posts: 15,390 Likes: 14 Fayetteville, NC EV607797 Moderator-Vertical, Vodavi, 1A2, Outside Wire
EV607797 Moderator-Vertical, Vodavi, 1A2, Outside Wire Joined: Jan 2005 Posts: 15,390 Likes: 14 Fayetteville, NC	I like it. Not bad at all for a first timer for sure. So, Matt did you decide to use the Teltone intercom in lieu of the 601 card? Gray cable ties? What gray cable ties? I didn't notice them. Ed Vaughn, MBSWWYPBX

Re: Project 1A2: Phase I complete. #484984 11/08/07 12:58 PM
Joined: Dec 2002 Posts: 9,429 Likes: 3 Beachwood jeffmoss26 Member
jeffmoss26 Member Joined: Dec 2002 Posts: 9,429 Likes: 3 Beachwood	This picture https://img216.imageshack.us/img216/352/11080717122my8.jpg Matt, you must have the same gray cable tie supplier that I have Jeff Moss Moss Communications Computer Repair-Networking-Cabling MBSWWYPBX, JGAE

Re: Project 1A2: Phase I complete. #484985 11/08/07 01:25 PM
Joined: Sep 2007 Posts: 741 Missouri Matt1964 Member
Matt1964 Member Joined: Sep 2007 Posts: 741 Missouri	Quote Originally posted by EV607797: I like it. Not bad at all for a first timer for sure. So, Matt did you decide to use the Teltone intercom in lieu of the 601 card? Gray cable ties? What gray cable ties? I didn't notice them. For now - I want to have everything in the KSU; but until I can figure out why it won't work consitently... I'll go with the Teltone. I'll be getting another 601A soon and see how it behaves in that.

Re: Project 1A2: Phase I complete. #484986 05/12/08 10:15 AM
Joined: May 2008 Posts: 17 Miami n4yqt Member
n4yqt Member Joined: May 2008 Posts: 17 Miami