atcomsystems.ca/forum Forums TDM Business Telephone Systems NEC Telephones & Systems K-CCIS From SV8100 to SV8100

I have two test system.
SV8100 connect to SV8100 (on same switch and have same network).

System A:
Send No: 2xxx
Ext :151010
IPL Address:192.168.2.201
SN: 255.255.255.0
DSP GW1: 192.168.2.200
DSP GW2: 192.168.2.202
Point Code: 10

System b:
Send No: 1520xx
Ext :2001
IPL Address:192.168.2.101
SN: 255.255.255.0
DSP GW1: 192.168.2.100
DSP GW2: 192.168.2.102
Point Code: 40

System A:

Program 10-12-03: 192.168.2.254
Program 10-12-09: 192.168.2.201
Program 10-12-10: 255.255.255.0
Program 10-19-01: DSP 01-04 Type: Used for Networking
Program 10-40-04: 4 ports
Program 14-05-01 Assign Trunks 9 ~ 12 Trunk Group 10
Program 14-13: TrunkGroup:10 CCISRouteID: 1
Program 22-02-01: Set Trunks 9 ~ 12 as Tie Line (LK6)

Program 84-26-01:
GW1: 192.168.2.200
GW2: 192.168.2.202

Program 84-26-02:
RTP Port: 30001
Program 84-26-03:
RTCP Port: 30002

Program 50-01-01:
Select Option 1 (Enable)
Program 50-02-03:
Assign Route ID 9 = 10

Program 50-03-01:
Destination Point Code: 40
SytemID 1
CCISRouteID 1
Ipaddress: 192.168.2.101

Program 50-15-01: Default 1
Program 50-15-02: 57000
Program 50-15-03: 59000

Program 11-01-01:
1xxx = Exten Length Number 6 digits
2 = F-route Length Number 4 digits

Program 44-02
DialDigit: 2
ServiceType: F-routetable AdditionalData: 1

Program 44-05:
TrunkGroup: 10
DeleteDialDigit: 0 AddDialDigitTale = 0
Maximum Dialing Digit: 4
CCISoverIPDestinationPC: 40

System B

Program 10-12-03: 192.168.2.254
Program 10-12-09: 192.168.2.101
Program 10-12-10: 255.255.255.0
Program 10-19-01: DSP 01-04 Type: Used for Networking
Program 10-40-04: 4 ports
Program 14-05-01: Assign Trunks 9 ~ 12 in Trunk Group 10
Program 14-13: TrunkGroup:10 CCISRouteID: 1
Program 22-02-01: Set Trunks 9 ~ 12 as Tie Line (LK6)

Program 84-26-01:
GW1: 192.168.2.100
GW2: 192.168.2.102

Program 84-26-02:
RTP Port: 30001
Program 84-26-03:
RTCP Port: 30002

Program 50-01-01:
Select Option 1 (Enable)
Program 50-02-03:
Assign Route ID 9 = 40

Program 50-03-01:
Destination Point Code: 10
SytemID 1
CCISRouteID 1
Ipaddress: 192.168.2.201

Program 50-15-01: Default 1
Program 50-15-02: 57000
Program 50-15-03: 59000

Program 11-01-01:
2xxx = Ext LengthNumber 4 digits
8 = F-route LengthNumber 1 digits

Program 44-02
DialDigit: 810
ServiceType: F-routetable AdditionalData: 1

Program 44-05:
TrunkGroup: 10
DeleteDialDigit: 1 AddDialDigitTale = 1
Maximum Dialing Digit: 5
CCISoverIPDestinationPC: 10

Program 44-06-01: AdditionalDialData: 15

TEST:
From System A to System B
System A : From ext 1510 dial 2001
Result :Nothing – System Silent

From System B to System A
System B: From ext 2001 (digital phone)dial 81010
Result :
- First Trunk of Trunk group 10 is in used
- Phone silent after dial 81010
- After hangup the call. The line 009 (first line of trunk group 10) is busy and can’t release
- After 4 calls, all trunks (trunk group 10) are busy
- The fifth call is busy tone.

What is problem? Please help me!

First question are you NEC certified on the system or are you trying to do this from the manual only?

I have 4 lisence K-CCIS on both systems. I try to do it follow VOIP Netwoking.pdf but it don't work.

I trying do it manual only! I haven't have certificate.

No one help because i don't have certificate?

No, that is not the case. It is just too much to go into in this forum.

Sorry quang, I wasn't snubbing you but what DrPBX said. There are so many things it COULD be as to be endless.